TLS Offshore Containers, TLS Special Containers
  • Home
    • About us
    • Quality, Health, Safety and Environment
    • Manufacturing standards
    • Container certificates
  • Containerised solutions
    • Intelligent pressurised container | MUD logging cabin
    • Battery energy storage system (BESS) container
    • Laboratory container | workshop container | Equipment containers
    • Temporary refuge shelter | Toxic gas refuge | Safe haven
    • Offshore accommodation cabin | office container
    • Reefer container | Refrigerated container
    • Intelligent waste water treatment container
    • Fresh water generator container
  • Cargo Containers
    • Offshore closed containers
    • Half height container
    • Cargo basket
    • Cutting skip, waste skip
    • Drum basket
    • Offshore Tank
    • Mini container
    • Open top container
  • Product photos & videos
  • News & Blogs
  • Contact us

TLS news & blogs

Container compressive capacity test: vertical impact test done by tls offshore containers int.

3/6/2023

 
The Container Compressive Capacity Test, also referred to as the Vertical Impact Test, is a widely used method for evaluating the safety performance of containers during transportation. This test is specifically designed to determine the compressive capacity of containers when subjected to vertical impact. The following testing criteria are strictly adhered to:
  1. The container is loaded with a uniformly distributed load equivalent to its rated weight, exclusive of the spreader, as well as the mass of the empty container along with its attachments, excluding the spreader. The load is then securely fastened.
  2. The testing is conducted on a flat concrete floor or any other hard ground, with wooden boards not exceeding a thickness of 50mm allowed to be placed on the ground.
  3. The container is tilted and lifted to an angle not less than 5° between the side beams and end beams connected to the lowest corner on the bottom of the container and the ground. The height difference between the lowest and highest corner points on the bottom surface of the container should not exceed 400mm.
  4. The lowest corner point of the container with the weakest stiffness is selected as the point of impact during the test.
  5. The container's initial impact velocity when touching the ground should not be less than 1m/s, and its lowest corner should be at least 50mm above the ground.
  6. Upon completion of the test, the container should not display any significant permanent deformation or damage, while minor repairable open welds and deformations are permitted.

TLS Offshore Containers Int. ensures that all of its products are meticulously produced and tested in strict compliance with international standards.
Written by Mandy


Comments are closed.

    Archives

    March 2023
    February 2023
    January 2023
    December 2022
    November 2022
    October 2022
    September 2022
    August 2022
    July 2022
    June 2022
    May 2022
    April 2022
    March 2022
    February 2022
    January 2022
    December 2021
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    May 2021
    April 2021
    March 2021
    February 2021
    January 2021
    December 2020
    November 2020
    October 2020
    September 2020
    August 2020
    July 2020
    June 2020
    November 2019
    October 2019
    September 2019
    July 2019
    June 2019
    May 2019
    February 2019
    October 2018
    September 2018
    August 2018
    December 2013

    Categories

    All
    A60
    Accommodation Cabin
    ADNOC
    BATTERY ENERGY STORAGE SYSTEM(BESS)
    Container Accessories
    Container Standards
    Container Test
    CUTTING SKIPS
    Drop Test
    Dry Container
    ESS Container
    FEA
    Feedback From Clients
    FREEZER
    Iso Container
    Laboratory Container
    LIFTING TEST
    MCC Shelter
    |MWD/LWD Cabin
    NEGATIVE PRESSURE
    Offshore Accommodation Module
    Offshore Living Quarter
    Offshore Workshop Container
    POSITIVE PRESSURE
    Pressurised Container
    PROCESS OF CONTAINER
    Reefer Container
    Refrigerated
    Refrigerated Container
    SEWAGE TREATMENT
    Temperature Control
    Temporary Refuge
    Temporary Refuge (TR) Shelter
    TLS OFFSHORE CONTAINER
    WATER TIGHTNESS
    WELDING INSPECTION
    Workshop Container

Featured products
Intelligent pressurised container
​Temporary refuge (TR) shelter, toxic gas refuge (TGR)​
​Battery e
nergy storage system (BESS) container
Containerised waste water treatment plant
Fresh water generator container
Reefer container
Laboratory container, Workshop container
Accommodation container
​
Offshore closed container
Company
About us

News & Blogs
Product photos & videos
Privacy policies
​Terms and conditions
Contact us
Communities
Facebook
​Twitter
Linkedin
Instagram
​Pinterest
​Flickr
Contact us
Email: sales@tls-containers.com
Hotline: +65-65637288; +65-31386967
All Rights Reserved 2020 © TLS Offshore Containers / TLS Special Containers
  • Home
    • About us
    • Quality, Health, Safety and Environment
    • Manufacturing standards
    • Container certificates
  • Containerised solutions
    • Intelligent pressurised container | MUD logging cabin
    • Battery energy storage system (BESS) container
    • Laboratory container | workshop container | Equipment containers
    • Temporary refuge shelter | Toxic gas refuge | Safe haven
    • Offshore accommodation cabin | office container
    • Reefer container | Refrigerated container
    • Intelligent waste water treatment container
    • Fresh water generator container
  • Cargo Containers
    • Offshore closed containers
    • Half height container
    • Cargo basket
    • Cutting skip, waste skip
    • Drum basket
    • Offshore Tank
    • Mini container
    • Open top container
  • Product photos & videos
  • News & Blogs
  • Contact us